How to reset airbag light on Hyundai Santa Fe?

to reset the airbag light on Hyundai Santa Fe without resetting the position of the airbag and without voiding the warranty, you can do it by unplugging the car from the 12V power source and press and hold the airbag warning light reset button (located on the driver’s side) for about 30 seconds.

The red light will turn off and the system will reset. You can reset the airbag warning light by pressing the turn signal switch located on the driver’s side of the steering column three times within 20 seconds. After you finish doing that, the warning light will turn off.

If it doesn’t turn off, you will have to check if the airbag is working properly. If the airbag is working properly, the light will turn off.

If the airbag is not working properly, you will need to have your airbag light reset

How to reset my Hyundai Santa Fe airbag light?

Your Hyundai Santa Fe airbag light either stays on or blinks. If you notice the dash board light is flashing, and not just the indicator light, it means your airbag warning light is on.

If the airbag warning light is on, it indicates that your airbags have been deployed and that there may be something wrong with your vehicle. If you want to reset your Hyundai Santa Fe airbag light, you will need to connect your car to your computer. To do this, plug in Your Hyundai Santa Fe airbag light might be flashing for no apparent reason.

If you're wondering why the airbag light is flashing, it may be because of the way your airbag is set up. To reset this indicator light, you'll need to press and hold the interlock switch for five seconds, then press it again to reset the light. If the light still blinks, you may have a wiring issue.

If you see a short in the wiring, you'll want to have this

How to reset Hyundai Santa Fe airbag light at start?

Firstly, check whether the airbag warning light is on or off and make sure it is not flashing. If the light is on but doesn’t flash, it could be an indicator that the airbag sensor is faulty. If the light does not appear at all, it means the system is disabled. You need to check whether the airbag is deactivated or not.

If it is, press the ignition switch to the start position and press the brake pedal at the same time (to prevent You can press the reset button of your Hyundai Santa Fe airbag light on the steering column for 5 seconds. The airbag light will turn to normal.

If the light still blinks, you will have to replace the airbag light. However, you can use the following DIY method to reset the light. This is only applicable if the airbag light is not flashing.

How to reset the airbag light on Hyundai Santa Fe?

If the airbag light on your Hyundai Santa Fe is on with no apparent reason, first check the system for any faults. We recommend getting a scan report from your vehicle to see if there is any damage to the car’s wiring that could be causing the light to stay on.

If there is no apparent fault, you could be looking at the airbag light reset issue and the following solution could help. If you’ve forgotten how to do it or can’t figure it When the airbag light is on, it means that the airbag warning signals are on. It is possible that the airbag warning light on the Hyundai Santa Fe is flashing due to sensor faults.

It is also possible that the airbag warning light is flashing due to a software or hardware issue. If the airbag warning light is flashing due to a software issue, you can reset the airbag warning light.

To reset the airbag warning light, you will need to enter the vehicle’

How to reset the airbag light on Hyundai Santa Fe rs?

If the airbag light on your Hyundai Santa Fe rs is on, then it’s possible that the airbags have been disabled. To reset the airbag light on the Hyundai Santa Fe rs, turn the key to the on position and release it. While doing so, make sure to keep the key in the ignition position. If the airbag light is still on, you will need to replace the front airbag, which will cost you around $70. If the light goes off, If you want to reset the airbag light on Hyundai Santa Fe rs, you can try clearing the fault codes stored in the car’s memory. To do this, the engine needs to be turned off. Remove the key from the ignition or at least switch it to the “off” position. Now press and hold the CUE button for 10 seconds. Once you press the button, the system will check for any faults and if it detects any, it will clear the codes.