What does rectified mean for porcelain tile?

When porcelain tiles are fired at high temperatures and under high pressure, they undergo a chemical reaction known as vitrification. While porcelain tiles are created during the heating process, the tiles are not completely cooled down until they are fired.

This chemical reaction repairs the tiles so that they are not damaged when the tiles are exposed to moisture. Rectification refers to the process of removing color from porcelain tiles. The most common method for removing color from porcelain tiles is chemical stripping.

This process involves applying a chemical solution to the tiles and then exposing them to a high-pressure water rinse. The chemical removes the color from the surface of the tile, leaving the porcelain unchanged.

What does rectified mean for thin porcelain tile installation?

Since porcelain tile is so thin, it is crucial to have the tiles set level and flat. If one or more of the tiles are not flat and level, you will end up with visible warps and cracks that will show through the grout.

To make sure the tiles are flat and level, use a porcelain tile laying guide or a tile square. Every tile should be set level at the same time and all tiles should be the same amount from the top of Since thinner porcelain tiles are thinner they often flex more than thicker tiles. To prevent cracking, the tiles must be installed properly.

A common mistake is to cut tiles too short or leave overhang. If the tiles are cut too short, they will crack. To prevent this, install tiles according to the manufacturer’s installation instructions. Leaving overhang is also a problem. If the tiles are set back too far from the wall, they can crack.

If the tile is flexing,

What does rectified mean for thin porcelain tile?

When people talk about porcelain tile, they very often refer to thin porcelain. The thickness of these tiles is around 6-8mm. The thinner the porcelain tile, the more chipped or broken it will be due to impact. To prevent damage to thinner porcelain tile, use a protective cushion, such as a piece of foam cushioning or newspaper.

Squeeze the cushioning between the tile and the wall to cushion the impact. When installing porcelain Very thin porcelain tile is often used for decorative wall tile, such as in bathroom walls. When the porcelain tile is very thin, it’s possible for it to have a slight warping.

This warping is called “cupping.” A tile with cupping undergoes a heating and cooling process which causes the tile to shrink and expand, respectively.

This expansion and contraction can break or crack the tiles, so it’s important to install thin por

What does rectified mean for porcelain tile thin?

When a porcelain tile becomes damaged, the tile may lose its original color and appearance, making it look different from its original shade and texture. This can be incredibly frustrating for homeowners, and sometimes it’s not clear whether the tile was damaged before or after being installed.

However, porcelain tile may also lose its color if it’s not properly sealed, so it’s important to make sure your porcelain tile is sealed properly to prevent color loss or fading The term “rectified” or “rectification” refers to the process of removing impurities and crystalline salts from raw kaolin clay.

It is performed by adding chemicals to the clay to extract the minerals. In the case of porcelain tile, the chemical added is potassium alum. The resulting material is heated to remove the impurities, leaving behind pure white kaolin clay.

What does rectified mean for porcelain tile installation?

When porcelain tiles are glazed, the tiles are heated to approximately 1,500 degrees so minerals in the clay align and form a smooth, glossy surface. To “rectify” porcelain tiles means they are fixed after firing. This can be done through two methods: chemical sealing or mechanical sealing. Chemical sealing involves adding a sealer to the tiles, while mechanical sealing involves sealing the tiles with a material that is applied after the tiles are fired. After sealing, tiles are When porcelain is made, some of the mineral salts used in the clay mixture crystallize to form crystals. These crystalline minerals create a natural beauty that gives porcelain its unique color and translucency. However, these naturally occurring minerals can also affect the color of the glaze and make it less colorfast. For this reason, porcelain tiles often need to be chemically “rectified” to restore their natural color to the glaze.